$119 HoverSeat XL - Sitting Attachment for Hoverboard (2023)

Deluxe Sitting Attachment for Hoverboards - HoverSeat XL™.

New hoverboard sitting attachment now comes with a built in comfortable chair!

  • We are now offering combo of HoverSeat XL and Hoverboard! Hoverboard has large 10" pneumatic wheels for smooth ride over any surface, including packed sand. And, our new hoverboards were already pre-calibrated with footpads facing rider under comfortable angle, instead of being horizontal. Click here to find out more about HoverSeat hoverboards.

Future of personal mobility has just arrived. Introducing HoverSeat XL - hands free, intuitive transportation device. Safely reach places too close to drive, quickly reach distances too far to walk. Zooming around in HoverSeat XL not only fun, but also gives liberating feeling of moving effortlessly to any directions you wish to go. No need for license, no need registration and no need for insurance. It’s an ultimate urban transporter. Fast, efficient and totally green mini electric vehicle that is unique and distinctively looking. Turn attention anywhere you go!

$119 HoverSeat XL - Sitting Attachment for Hoverboard (1)

Benefits of HoverSeat XL:

  • The HoverSeat XL is a light aluminum frame which fits easily in the trunk of the car. When you want to use it, simply attach it to the bar in the center of your hoverboard with the specially adapted clamp, flip up back rest, and you are ready to roll!
  • HoverSeat XL comes with soft and comfy sport seat with generous back pack storage and armrest side pouch with space for bottle and cell phone. Backrest angle is adjustable for best comfort. Store HoverSeat XL vertically when not in use.
  • Navigate the hoverboard using only your feet; it can even reverse. HoverSeat XL can be used on or off-road, and can ride over grass, gravel, and packed sand.
  • Use HoverSeat XL to tow a wheeled cart and then transport bags, boxes, groceries, or use it to transport heavy or awkward tools. The hoverboard cart is even strong enough to pull a kayak down to the beach.
  • No need to carry your hoverboard ever again: Use HoverSeat XL to transport your hoverboard back home or back to the car when the charge has gone.
  • Safer than standing on a hoverboard: No more falling off when the hoverboard hits a crack or bump in the pavement. Sitting is far safer than standing.

HoverSeat XL Instructions:

  • Click on ATTACHMENTS tab to download HoverSeat Manual and Assembly Instructions.
  • HoverSeat XL Frequently Asked Question (FAQ)

What is included with a HoverSeat XL?

  • Aluminum frame with 2 ball bearing wheels and Patent Pending HoverClamp.
  • Deluxe chair built into HoverSeat frame.
  • Plastic clamp for round center hoverboards incldued.
  • Assembly required. Please refer above Assembly instructions.
  • Shipping size: 37"x21"x4.5". Shipping Weight: 16lbs.
  • Product weight is 13lbs.
  • Rider weight limit 180 lbs.

Where to get hoverboard for HoverSeat XL?

  • For best performance and riding pleasure we recommend 10" pneumatic wheels hoverboard. It provides softer rider over pavement and better off-road capability. You can purchase inexpensive 10" hoverboard on Ebay, or just search Google for 10" hoverboard. Please note that hoverboard must have round middle to work with our clamp.

Videos of Seating Attachment for Hoverboard - HoverSeatXL


The user of this product assumes all risks associated with its use. Rider assumes all risks associated with activity. Make sure the environment is safe for riding. Make sure all bolts are secure. Inspect clamp for cracks or damages. Use all necessary body protectors. MUST wear helmet, knee, elbow pads, wrist guard, exercise full caution when driving, be prepared to stop. Do NOT operate where people or cars might be present. Do NOT ride on slopped areas. Do NOT overload. Do NOT race. Do NOT lift feet of pads while driving. HoverSeat is not disability vehicle transportation. This product should not be used by persons without excellent vision, balance, coordination, reflex, muscle and bone strength or good decision making capability. This product should not be used by minor without adult supervision. This product should not be used by persons unwilling or unable to take responsibility for their own action. To minimize assumed risks, the user must wear helmet, elbow and keen pads and appropriate shoes. Do not operate this product in traffic, wet, froze, oily or unpaved surfaces. Avoid uneven surfaces, chuckholes, cracks and obstacles.

Clamp provided with HoverSeat will work only with these round center hoverboards:

DIY Clamp for non-round hoverboards (Custom_clamp.pdf, 1,533Kb) [Download]

HoverSeatXL Manual (HoverSeatXL-Manual.pdf, 932Kb) [Download]

HoverSeatXL Assembly Instructions Page 1 (Assembly_Page_1.pdf, 1,380Kb) [Download]

HoverSeatXL Assembly Instructions Page 2 (Assembly_Page_2.pdf, 1,354Kb) [Download]

Q. What is the warranty for HoverSeats XL?
A. The Manufacturer Warranty for the HoverSeat aluminum frame, wheels and clamp is one year from the date of product delivery. Please keep all sales receipts to claim the warranty. No warranty will be covered without a sales receipt. The warranty does NOT cover scratches, discolorations, rubber layers delamination, tie downs, plastic T-handle or accidental damages due to product use. We will repair or replace defective parts at our discretion. Customers are responsible for all shipping charges associated with warranty services. The defective item must be delivered back to us for inspection, repairs or replacement. To initiate a customer request, please email us a picture showing the nature of the damage, an overall picture of the product and the order number or name on the order.

Q. What is return policy for HoverSeat XL?
A. You have 30 days from date of delivery to return HoverSeat product back for a refund. We suggest watching instructional video to make sure you are properly using HoverSeat with a hoverboard. Please keep all receipts, boxes and packing materials. While we understand that product can't be returned in a brand new condition, it is however customer's responsibility to clean up all signs of use that can be removed, such as: wipe clean all dirt and dust, wash wheels, remove any type of dirt, grime and dust from all components. If we have to clean product after return, then we will have to charge re-stocking fees. Please pack everything exactly same way as you received it, and send back to address on a shipping label, only after receiving RMA number from us via email. Refund will be issued via company check for product price, less shipping charges. Shipping charges are NOT refundable. Please email 2 weeks after return for refund status update.

Q. What is included with the HoverSeat XL?
A. The HoverSeat XL product includes: aluminum frame that requires simple assembly, two pneumatic wheels, plastic clamp that secures to the middle of the hoverboard, and a product manual. Also included as a free bonus is one plastic T-handle that can be installed in order to provide an additional option for pulling a cart by hand, if needed.

Q. What hoverboard do you recommend for HoverSeat XL?
A. If you don't have yet a hoverboard, and thinking about buying one to use with HoverSeat, then we suggest getting 10" hoverboard with pneumatic wheels. Its feel very nice to ride, can be used off-road, and provide most comfortable ride. Small 6" hoverboard with non-pneumatic rubber wheels feels too bumpy and hard on a regular urban pavement that is covered with cracks and joints. Hoverboards with 6" wheels can be used on a smooth asphalt or concrete surface, but become rough on a pavement with multiple cracks, blocks and bricks type of pavements. HoverSeat clamps will not work with 8" wheels hoverboards, because they don't have round middle part. Also, 6" hoverboard with all flat top also will not work with our round clamp.

Q. How fast and how long can the HoverSeat XL ride?
A. The HoverSeat's overall performance fully relies on the hoverboard it’s attached to. How fast and how long the HoverSeat will ride depends on numerous factors, including road conditions, weight load, hoverboard battery capacity and motor power rating. It is recommended that all wheels be fully inflated to the maximum allowed pressure to provide the best performance. Softer wheels will reduce vibration but will also drain the battery more quickly, as core power is required to turn underinflated wheels.

Q. Is it possible to damage a hoverboard with the HoverSeat XL?
A. We extensively tested the HoverSeat with weights up to 230 lbs, and there was no physical damage to the hoverboard's structure or internal parts. We even towed two people with a total weight well over 300 lbs with no damage to the hoverboard. However, depending on the weight of a rider and the manner of operation, it might be possible to scratch the surface of the hoverboard in the area where the clamp attaches to the hoverboard. The clamps are covered with a soft protective layer, but it still might be possible to slightly scratch the hoverboard's painted surface. Therefore, if keeping the hoverboard looking flawless is a concern, we recommend applying optional protective skins or attaching clear scotch tape at the area where the HoverSeat clamp touches the hoverboard.

Q. How do I install the T-handle?
A. The T-handle is an optional item that can be installed by the customer if needed. It is provided for additional convenience if it becomes necessary to pull the HoverSeat with the hoverboard on top. You will need to use a flat screwdriver to pull out the rectangular plastic end cap from the end of the front pull tube, then slide the T-handle into the opening and secure it with the provided screw at the bottom of the pull tube.

Q. Is it possible to fall from a HoverSeat XL?
A. The short answer is YES. As with any other type of vehicle, there are always risks associated with its operation due to various reasons. The HoverSeat operates attached to the hoverboard. Therefore, its performance strongly depends on the hoverboard's characteristics and user experience. If, during forward movement, the hoverboard stops suddenly either due to its failure or the operator's failure to properly engage the pressure sensors, that might result in a fall forward and possible injuries. Some inferior hoverboard models might have faulty pressure and gyroscopic sensors that can fail during operation. Therefore, it is imperative to drive slowly when using the HoverSeat for the very first time, and take time to accustom yourself to the HoverSeat's behavior and hoverboard operations. The customer should wear protective gear, such as a helmet and knee and wrist pads during HoverSeat operation. The customer should hold on to the chair to provide additional support in case of sudden stops, which may cause them to slide forward. Please read all posted warnings and the owner's manual before operating the HoverSeat. Please inspect all HoverSeat components before each ride for loose screws or cracks in the clamp attached to the hoverboard. However, it also should be noted that even though the remote risk of injury might still exist while operating the HoverSeat, it is much less severe than the type of injuries associated with falling from a hoverboard while standing.

Q. Does the HoverSeat XL work with all hoverboards?
A. Currently, the HoverSeat clamp is designed to work only with hoverboards that have a rounded middle part, like most 6” and 10” hoverboards. Some hoverboards might not have a rounded center, and therefore, the clamp will not wrap properly around it. So-called Lamborghini 8” hoverboards do not have rounded middles and therefore are not compatible with the current design of the HoverSeat clamp. In the future, we might offer an improved clamp that can go over any type of hoverboard.

Q. Why did my hoverboard start vibrating violently when I put my feet on the footpads to start riding?

A. Hoverboards are designed to sense when a person is standing on top of it. There are two pressure sensors located on each footpad, closer to the wheels. All four sensors need to be pressed down before the hoverboard can start moving. If any of these four sensors are not engaged, most hoverboards will start shaking and vibrating, and may even rotate over the center. When using the HoverSeat with a hoverboard, it is important to place both feet on the footpads in such way that the weight of your feet will press on the sensors under the footpads. For most adults, the weight of their feet simply placed on top of hoverboards should be enough to engage the sensors. There is no need to press down hard. However, some hoverboards with less sensitive sensors might require more effort in pressing down in order to engage the sensors. Also, younger kids and smaller adults might not have enough weight in their feet to press down on the sensors. In cases like that, we recommend optional ankle weights that are used for exercise and sold in major retail stores in the sports section. Placed over the ankles, these weights might help to press down on the sensors. However, it must be noted that the HoverSeat might not be for everyone, and younger kids might not be able to operate it properly. For that purpose, we are developing a hands-only operation attachment.

Q. How can I calibrate the hoverboard so that the footpads are turned toward the HoverSeat XL?

A. Most hoverboards allow calibration that is designed to keep the footpads horizontal for standing. This feature can also be used to have the footpads turned toward the hoverboard at an angle, which makes it much easier to operate the HoverSeat. To re-calibrate your hoverboard, you will need to press the power button and hold it down for a few seconds until the LED lights blink or you hear a beep. Turn it off and back on, and now when you sit on the HoverSeat and put your feet on the hoverboard, you will feel that the footpads are operational at an angle instead of being horizontal. It is very important not to touch the footpads while re-calibrating the hoverboard, because it may cause damage to the gyroscopic sensor in some hoverboards. If that happens, the LED lights on the damaged side will stay on after turning the hoverboard on. It is easy to replace the gyroscopic sensor, and they are available on eBay and Amazon. There are plenty of YouTube videos showing how to replace hoverboard sensors.

Q. What accessories are available for the HoverSeat XL?
A. Many regular bicycle accessories can be adapted for HoverSeat use. For example, LED bicycle lights in silicone or rubber housing can be easily wrapped around the HoverSeat frame or beach chair tubing. An electric bike horn can be installed directly on a chair, and quick-release bicycle bottle holders can be attached to both the frame and the beach chair mounted on the HoverSeat. Additional accessories such as an iPad gooseneck stand can be secured to the clamp to provide GPS location or entertainment during your ride. Sun umbrellas can be mounted on top of the beach chair to provide shade during hot days. Possibilities to accessorize the HoverSeat are endless.

Q. What air pressure should I put into hoverboard and HoverSeat XL tires?
A. You can pump tires up to recommended pressure that is printed on a tire sides. When tire is hard, 10" hoverboard uses less energy to pull HoverSeat behind it. However, when hoverboard and HoverSeat tires are softer, that will provide more cushioned, comfortable ride. If you feel that 10" hoverboard is too jumpy on obstacles and provide bumpy ride, then release a little bit of pressure in its tires, and you immediately will feel the difference. Do not make tires to soft, because it will run down battery quicker and air stem can move from its position during ride.

Q. Why my hoverboard shakes violently when I put my feet on it?
A. There are 4 pressure sensors under 4 outer corners of footpads on top of hoverboard. All 4 pressure sensors need to be engaged to tell hoverboard that someone is standing on hoverboard before it can ride forward. Therefore each foot should lay flat against each foot pad in order to engage pressure sensors. Weight of each foot should be enough to have sensors pressed down. However, if weight of foot is not enough, then way around it is to install tubes that come with our new handles manual attachment. These tubes tightened to edges of footpads with tie downs in order to keep pressure sensors always engaged. Then hoverboard can be used with or without handles.

Q. How can I improve HoverSeat XL to make it even better?

A. Please see below video showing some additional modifications for hoverboard that can significantly improve HoverSeat set up with hoverboard.

By replacing internal hoverboard battery with internal bicycle battery, not only you will eliminate even remote risk of a fire, but also you will make hoverboard itself much lighter, and will increase driving range over 3 times! It is also much easier to simply detach battery from HoverSeat for charging, then to carry heavy hoverboard all way to power outlet.

Additional suggested mod to make experience of riding hoverboard with HoverSeat even more easier, is to cover photoelectric pressure sensors on gyroscopic boards with scotch or duct tape, so that pressure sensors are always on. If you are not going to ride hoverboard standing anymore, then there is no need for pressure sensors. Once pressure sensors are always engaged, that means there is no more need to keep pressing with foot on a surface of foot pads when riding HoverSeat. It will eliminate hoverboard vibration, risk of sudden lose of control, and will makes whole experience much better. With pressure sensors always "on", it just enough to press anywhere on hoverboard surface to propel hoverboard forward. However, it is important do angle calibration before closing sensors, because calibrating hoverboard with pressure sensors engaged can damage gyros.

Q. How can I make HoverSeat to work with other hoverboards without round middle?

A. Clamp provided with HoverSeat designed to fit only over hoverboards with round middle.While we do not offer out-of-box solution for other types of hoverboards, such as 8" wheel for example, below are some suggested DIY clamps that might work with other type of hoverboards. Pictures provided for reference only. We do not make these clamps and do not provide additional suggestions.

Q. What to do if I am unable to re-calibrate my hoverboard foot pads to operate under angle?

A. Here is suggested work around using cheap yoga foam blocks that are sold in many retail stores. Just cut block diagonally, to make 2 wedges. Drill or cut 2 holes at edges, and run tie downs through holes. Make knots at ends of tie downs and use washers, so that knots will not slip out of holes in a foam. Attach wedges to foot pads of hoverboard with tie downs, such way that foot pads sensors remained engaged. This way you can easily operate hoverboard with wedges translation pressure down to foot pads.

Another easy option is to use 2 pcs of Industrial Rubber Wedges sold on Amazon at $14/pc and simply secure both wedges on top of foot pads with 2 adjustable tie downs. That will allow operation of hoverboard with footpads facing HoverSeat rider.

Top Articles
Latest Posts
Article information

Author: Reed Wilderman

Last Updated: 05/28/2023

Views: 6474

Rating: 4.1 / 5 (72 voted)

Reviews: 87% of readers found this page helpful

Author information

Name: Reed Wilderman

Birthday: 1992-06-14

Address: 998 Estell Village, Lake Oscarberg, SD 48713-6877

Phone: +21813267449721

Job: Technology Engineer

Hobby: Swimming, Do it yourself, Beekeeping, Lapidary, Cosplaying, Hiking, Graffiti

Introduction: My name is Reed Wilderman, I am a faithful, bright, lucky, adventurous, lively, rich, vast person who loves writing and wants to share my knowledge and understanding with you.